Aleromod.com Aleromod.com

Go Back   Aleromod.com > General Help > How-To Archive & FAQ

Reply
 
Thread Tools Search this Thread Display Modes
Old 06-14-2011, 06:03 PM   #1
Brad Jahnke
 
Posts: n/a
LED turn signals with load regulators

This is my first attempt at writing a how to. I apologize for the quality of the photos as the only camera I have is on my phone. Also, this writeup was written on my phone, so if you have any additional questions, please feel free to message me.


Steps for converting turn signals from incandescent bulbs to LED bulbs with load regulators.

Front turn signals:

1.) Remove your headlight fixture by lifting the two clips on the top of the assembly.


2.) Remove the power plug and the bulbs from the assembly.

3.) Remove the plastic shielding from around your turn signal wires.


4.) The blue wire is positive and the black wire (or grey in some cases) is ground. Clip one end of your regulator and your ground wire together.


5.) Clip the other wire on the regulator to the positive (blue) wire.


6.) Find a suitable mounting spot for the regulator itself. I used high heat double sided sticky tape from 3M and just stuck it to the underside of my bumper. Just remember, the regulators do get hot and if you don't use high heat tape, you'll have a dangling regulator.

7.) Reinstall the bulbs, reconnect the power and reinstall your headlight assembly.

8.) Repeat this step by step for the other side.


Rear turn signals:

1.) Remove the two screw caps holding the fabric against your trunk.


2.) Remove the three plastic wingnuts holding your outer taillight in place.


3.) Remove the bulbs from the fixture, the one with the white plastic is your turn signal. It has 2 wires - one black, one blue - going into it.


4. As with the front signals, blue is positive, black is negative. Clip one end of the regulator to the blue wire.


5.) Clip the other end of the regulator to the black wire.


6.) Mount your regulator with the double sided high heat tape. I mounted mine right below where the taillight assembly sits.


7.) Reassemble everything and repeat these steps for the other side.
  Reply With Quote
Old 06-14-2011, 06:25 PM   #2
spc2125
GLS member
 
spc2125's Avatar
 
Join Date: Oct 2010
Location: MA
Posts: 1,369
spc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond repute
excuse my noobish question but where are the LEDs?
__________________
just call me "Doc"
HID 55W 8000K lowbeam headlights~~Sony Deck~~2 12 in alpine type r subs/ alpine amp
Tinted tail lights~~CAI~~Pacesetter Headers~~ Magnaflow High Flow Cat~~Catback Exhaust System
Check out my alero!
Aleromod Showcase Video
spc2125 is offline   Reply With Quote
Old 06-14-2011, 06:27 PM   #3
Brad Jahnke
 
Posts: n/a
That *should* be fairly self explanitory...I hope?
  Reply With Quote
Old 06-14-2011, 06:31 PM   #4
spc2125
GLS member
 
spc2125's Avatar
 
Join Date: Oct 2010
Location: MA
Posts: 1,369
spc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond repute
there obviously still at the store because i dont see any in these pictures
__________________
just call me "Doc"
HID 55W 8000K lowbeam headlights~~Sony Deck~~2 12 in alpine type r subs/ alpine amp
Tinted tail lights~~CAI~~Pacesetter Headers~~ Magnaflow High Flow Cat~~Catback Exhaust System
Check out my alero!
Aleromod Showcase Video
spc2125 is offline   Reply With Quote
Old 06-14-2011, 06:34 PM   #5
Brad Jahnke
 
Posts: n/a
Kinda funny because I have an invoice for $202.37 from superbrightleds
  Reply With Quote
Old 06-14-2011, 06:38 PM   #6
Brad Jahnke
 
Posts: n/a
Also, in my opinion, if someone doesn't know how to install a wedge based light bulb, they probably shouldn't be installing load regulators. I figured it would be a no brainer so I left that part out. I'm sorry.
  Reply With Quote
Old 06-14-2011, 06:38 PM   #7
cherrington17
Gone
 
cherrington17's Avatar
 
Join Date: Mar 2004
Location: Lockport Ny
Posts: 19,244
cherrington17 has a spectacular aura aboutcherrington17 has a spectacular aura about
Send a message via AIM to cherrington17


*cough* in picture *cough*
__________________
Frequently Asked Questions
...You only stop learning when your dead...
cherrington17 is offline   Reply With Quote
Old 06-14-2011, 06:48 PM   #8
spc2125
GLS member
 
spc2125's Avatar
 
Join Date: Oct 2010
Location: MA
Posts: 1,369
spc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond repute
Quote:
Originally Posted by Brad Jahnke View Post


1.) Remove your headlight fixture by lifting the two clips on the top of the assembly.

So you can show how to lift two clips but you can't show which bulbs you put in
hmm....
__________________
just call me "Doc"
HID 55W 8000K lowbeam headlights~~Sony Deck~~2 12 in alpine type r subs/ alpine amp
Tinted tail lights~~CAI~~Pacesetter Headers~~ Magnaflow High Flow Cat~~Catback Exhaust System
Check out my alero!
Aleromod Showcase Video
spc2125 is offline   Reply With Quote
Old 06-14-2011, 06:50 PM   #9
alero_bmxer
GL Member
 
alero_bmxer's Avatar
 
Join Date: Jan 2009
Location: Fowlerville MI
Posts: 874
alero_bmxer has a reputation beyond reputealero_bmxer has a reputation beyond reputealero_bmxer has a reputation beyond reputealero_bmxer has a reputation beyond reputealero_bmxer has a reputation beyond reputealero_bmxer has a reputation beyond reputealero_bmxer has a reputation beyond reputealero_bmxer has a reputation beyond reputealero_bmxer has a reputation beyond reputealero_bmxer has a reputation beyond reputealero_bmxer has a reputation beyond repute
^must you be a jackass and start shit over the internet? haha
__________________
[ion] C2 - I ran her hard, on nothing but the bare ground. After easing into it and progressively pushing down harder I could feel the pressure building and once it peaked I let off and she gave a loud cry from the blow off valve.
Ttop191 - ^ because your car is the only thing that will suck and blow that you can actually successfully get within 25 feet of

alero_bmxer is offline   Reply With Quote
Old 06-14-2011, 06:54 PM   #10
Brad Jahnke
 
Posts: n/a
Its cool...ill just have the thread deleted and he can do it himself.
  Reply With Quote
Old 06-14-2011, 07:01 PM   #11
spc2125
GLS member
 
spc2125's Avatar
 
Join Date: Oct 2010
Location: MA
Posts: 1,369
spc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond reputespc2125 has a reputation beyond repute
ive just never seen led bulbs like that. i have the ones that like 9 or 12 tiny bulbs. so when i saw the picture it looked like the stock bulb.. hense the where is the LED
__________________
just call me "Doc"
HID 55W 8000K lowbeam headlights~~Sony Deck~~2 12 in alpine type r subs/ alpine amp
Tinted tail lights~~CAI~~Pacesetter Headers~~ Magnaflow High Flow Cat~~Catback Exhaust System
Check out my alero!
Aleromod Showcase Video
spc2125 is offline   Reply With Quote
Old 06-14-2011, 07:04 PM   #12
Brad Jahnke
 
Posts: n/a
Those are the stock bulbs. As I stated, in my opinion, if someone can't change a bulb, they shouldn't be installing regulators. I just left out the parts that a monkey could do.
  Reply With Quote
Old 06-14-2011, 07:28 PM   #13
JLw7123
i speed up for corners
 
JLw7123's Avatar
 
Join Date: Apr 2009
Location: Dover,NH
Posts: 3,489
JLw7123 is on a distinguished road
Send a message via AIM to JLw7123 Send a message via Yahoo to JLw7123 Send a message via Skype™ to JLw7123
doesn't look to hard to do i might do this on my free time at college. I would be a good project for my electronics class for automotive.
__________________
[SIGPIC]
Alero is gone but not forgotten
1999 black gls coupe R.I.P 130k
1999 auburn mist metallic gls sedan R.I.P
2005 Subaru legacy 2.5i 190k. New rims and tires for summer.
JLw7123 is offline   Reply With Quote
Old 06-14-2011, 07:52 PM   #14
Brad Jahnke
 
Posts: n/a
Its not hard to do...especially if u know how to install a bulb lol...took me 90 minutes to replace stop lights, turn signals, tail lights and the 3 in my gauge cluster that I hadn't replaced.
  Reply With Quote
Old 06-14-2011, 07:56 PM   #15
JLw7123
i speed up for corners
 
JLw7123's Avatar
 
Join Date: Apr 2009
Location: Dover,NH
Posts: 3,489
JLw7123 is on a distinguished road
Send a message via AIM to JLw7123 Send a message via Yahoo to JLw7123 Send a message via Skype™ to JLw7123
lol i know how to install bulbs and regulators.
__________________
[SIGPIC]
Alero is gone but not forgotten
1999 black gls coupe R.I.P 130k
1999 auburn mist metallic gls sedan R.I.P
2005 Subaru legacy 2.5i 190k. New rims and tires for summer.

Last edited by JLw7123 : 06-14-2011 at 08:00 PM.
JLw7123 is offline   Reply With Quote
Old 06-15-2011, 01:03 AM   #16
Philbar71
GL Member
 
Join Date: Jan 2010
Location: Suffolk, Virgina
Posts: 609
Philbar71 is on a distinguished road
Good guide! Night time pics please?
__________________
01 Alero 2.4 - Just minor mods...
Philbar71 is offline   Reply With Quote
Old 04-13-2013, 08:01 PM   #17
MiLo
GX Member
 
MiLo's Avatar
 
Join Date: Feb 2013
Location: Ill I No I iS
Posts: 199
MiLo is on a distinguished road
Quote:
Originally Posted by Brad Jahnke View Post
Its cool...ill just have the thread deleted and he can do it himself.

DAMN i guess he didnt get a chance to delete the post but he sure did delete the pix..

OK does anyone else have any pix to replace these pix or can someone do another HOW TO???
__________________
2004 GL1 2.2L Ecotec 160k mi. (Olympic White)
8000k 35w HID's
30/30 LED Switchback Turn Signals
JVC kw-hdr720 Double Din Head Unit
Polk Audio DXi691 Coaxial & DXi461 Plate Speakers
White/Glossified Plasti-Dipped OEM 15" Rims
Red Painted Brake Calipers & Drums
CarDomain home page is pretty much before pix.
The after pix haven't been taken yet... Still under construction
MiLo is offline   Reply With Quote
Old 04-13-2013, 10:58 PM   #18
tw0123
OSV coming soon!!!!!
 
tw0123's Avatar
 
Join Date: Jun 2006
Location: lindsay, ontario
Posts: 2,375
tw0123 has a reputation beyond reputetw0123 has a reputation beyond reputetw0123 has a reputation beyond reputetw0123 has a reputation beyond reputetw0123 has a reputation beyond reputetw0123 has a reputation beyond reputetw0123 has a reputation beyond reputetw0123 has a reputation beyond reputetw0123 has a reputation beyond reputetw0123 has a reputation beyond reputetw0123 has a reputation beyond repute
the instructions are still there, just no pictures... just follow what was typed and you are good to go!! who needs pictures lol jk!!
__________________

Misty: 3400, S&S headers, TCE 65mm TB, CAI, 180* TStat, Milzy motor & tranny mount, 18" BOSS 328 & much more... going osv!!
Silver: 2.4L, 5 speed, GAGT seats, front & rear STB's, all red tails, led headlights, Magnaflow muffler, Milzy Motor mount, WAI, Cosmo short shifter; sold n missed
Tequila: 2.4L, GA interior swap, scrapped...
tw0123 is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 08:37 AM.


Powered by vBulletin Version 3.6.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.