01-28-2016, 08:47 AM
|
#1
|
|
GX Member
Join Date: Dec 2015
Location: Ashland WI
Posts: 12
|
Cam Position sensor
I have a code for Camshaft position sensor on my 03 2.2 Ecotec. I have been looking on the internet and searched here. Do they have one? Or does it use the crank sensor? Also, I think I fixed my oil usage problem, replaced the $6 hose that runs from the valve cover to the air box, still on full after three weeks, was using half a quart a week. Thanks for the help.
|
|
|
|
01-28-2016, 10:02 AM
|
#2
|
|
GX Member
Join Date: Dec 2015
Location: Grand Ledge, MI
Posts: 177
|
|
|
|
|
|
01-28-2016, 08:14 PM
|
#3
|
|
GX Member
Join Date: Dec 2015
Location: Ashland WI
Posts: 12
|
Thanks, but the L61 2.2 ecotec is different from the LN2 2.2 ecotec, for some reason. There is no Camshaft sensor in that location. My trouble code is: PO340B, Camshaft position sensor circuit, so it would have to have one, right?
|
|
|
|
|
01-29-2016, 09:23 AM
|
#5
|
|
GX Member
Join Date: Dec 2015
Location: Ashland WI
Posts: 12
|
Yes, It does run. Engine has 230,000 miles on it. It runs well cold, kind of stumbles under load when warm. Plugs are new and contacts for ignition are clean with dielctric grease on them. Going to do a compression test. It used a half quart of oil in three weeks, no long distance driving.
|
|
|
|
|
01-29-2016, 10:05 AM
|
#6
|
|
GX Member
Join Date: Dec 2015
Location: Grand Ledge, MI
Posts: 177
|
Sounds like you went through the link I provided? I wish the best for you, but reading through that link again and very similar except yours runs.
Pat
|
|
|
|
|
01-31-2016, 07:48 PM
|
#7
|
|
GX Member
Join Date: Dec 2015
Location: Ashland WI
Posts: 12
|
So, did a compression test today, here are the results from the right: 170, 165, 155, 183. I put oil in number 2 and 3, they both came up to 215. Valves are probably good, engine is just wore.
|
|
|
|
|
01-31-2016, 08:39 PM
|
#8
|
|
GX Member
Join Date: Dec 2015
Location: Grand Ledge, MI
Posts: 177
|
Someone will have to confirm, but does not sound to bad.
Pat
|
|
|
|
|
02-01-2016, 09:34 AM
|
#9
|
|
GL Member
Join Date: Dec 2013
Location: Minnesota
Posts: 593
|
Compression is fine so I doubt it's the rings. I would say it's the valve guides in the head or it's leaking it. Half quart of oil ain't nothing. Even new cars can use oil. My 3.4 with 162,000 on it uses a quart in like 1,500 miles. I'm not worried. I had a Topaz that used a quart a week. Drove it for 3 years and never worried.
|
|
|
|
|
02-02-2016, 09:26 AM
|
#10
|
|
GX Member
Join Date: Dec 2015
Location: Ashland WI
Posts: 12
|
Thanks, Just going to drive it.
|
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
|
| Thread Tools |
Search this Thread |
|
|
|
| Display Modes |
 Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -4. The time now is 05:57 PM.
|
07 and up had them. 
